收藏本站
Data Sheet
Integration Time Under Steady Load
The discrete time sample period (T) for the accumulation register
is 0.4 μs (4/CLKIN). With full-scale sinusoidal signals on the
ADE7758
simple, single-wire, optically isolated interface to external
calibration equipment. Figure 69 illustrates the energy-to-
frequency conversion in the ADE7758 .
analog inputs and the watt gain registers set to 0x000, the average
word value from each LPF2 is 0xCCCCD (see Figure 65 and
INPUT TO AWATTHR
REGISTER
APCFNUM[11:0]
Figure 67). The maximum value that can be stored in the watt-
hr accumulation register before it overflows is 2 15 ? 1 or 0x7FFF.
INPUT TO BWATTHR
REGISTER
+
+
+
DFC
÷
÷4
APCF
Because the average word value is added to the internal register,
which can store 2 40 ? 1 or 0xFF, FFFF, FFFF before it overflows,
INPUT TO CWATTHR
REGISTER
APCFDEN[11:0]
the integration time under these conditions with WDIV = 0 is
Figure 69. Active Power Frequency Output
calculated as
Time =
0xFF, FFFF, FFFF
0xCCCCD
× 0.4 μs = 0.524 sec
(21)
A digital-to-frequency converter (DFC) is used to generate the
APCF pulse output from the total active power. The TERMSEL
bits (Bit 2 to Bit 4) of the COMPMODE register can be used to
When WDIV is set to a value different from 0, the time before
overflow is scaled accordingly as shown in Equation 22.
select which phases to include in the total power calculation.
Setting Bit 2, Bit 3, and Bit 4 includes the input to the AWATTHR,
Time = Time ( WDIV = 0) × WDIV [7:0]
(22)
BWATTHR, and CWATTHR registers in the total active power
calculation. The total active power is signed addition. However,
Energy Accumulation Mode
The active power accumulated in each watt-hr accumulation
register (AWATTHR, BWATTHR, or CWATTHR) depends on
the configuration of the CONSEL bits in the COMPMODE
register (Bit 0 and Bit 1). The different configurations are
described in Table 10.
Table 10. Inputs to Watt-Hr Accumulation Registers
CONSEL[1, 0] AWATTHR BWATTHR CWATTHR
00 VA × IA VB × IB VC × IC
01 VA × (IA – IB) 0 VC × (IC – IB)
10 VA × (IA – IB) 0 VC × IC
11 Reserved Reserved Reserved
Depending on the poly phase meter service, the appropriate
formula should be chosen to calculate the active energy. The
American ANSI C12.10 Standard defines the different
configurations of the meter.
Table 11 describes which mode should be chosen in these
different configurations.
Table 11. Meter Form Configuration
setting the ABS bit (Bit 5) in the COMPMODE register enables
the absolute-only mode; that is, only the absolute value of the
active power is considered.
The output from the DFC is divided down by a pair of frequency
division registers before being sent to the APCF pulse output.
Namely, APCFDEN/APCFNUM pulses are needed at the DFC
output before the APCF pin outputs a pulse. Under steady load
conditions, the output frequency is directly proportional to the
total active power. The pulse width of APCF is 64/CLKIN if
APCFNUM and APCFDEN are both equal. If APCFDEN is
greater than APCFNUM, the pulse width depends on APCFDEN.
The pulse width in this case is T × ( APCFDEN /2), where T is
the period of the APCF pulse and APCFDEN /2 is rounded to
the nearest whole number. An exception to this is when the
period is greater than 180 ms. In this case, the pulse width is
fixed at 90 ms.
The maximum output frequency (APCFNUM = 0x00 and
APCFDEN = 0x00) with full-scale ac signals on one phase is
approximately 16 kHz.
The ADE7758 incorporates two registers to set the frequency of
APCF (APCFNUM[11:0] and APCFDEN[11:0]). These are
ANSI Meter Form
CONSEL (d)
TERMSEL (d)
unsigned 12-bit registers that can be used to adjust the frequency of
5S/13S
6S/14S
8S/15S
9S/16S
3-Wire Delta
4-Wire Wye
4-Wire Delta
4-Wire Wye
0
1
2
0
3, 5, or 6
7
7
7
APCF by 1/2 12 to 1 with a step of 1/2 12 . For example, if the
output frequency is 1.562 kHz while the contents of APCFDEN
are 0 (0x000), then the output frequency can be set to 6.103 Hz
by writing 0xFF to the APCFDEN register.
Active Power Frequency Output
Pin 1 (APCF) of the ADE7758 provides frequency output for
the total active power. After initial calibration during manufac-
turing, the manufacturer or end customer often verifies the
energy meter calibration. One convenient way to verify the
meter calibration is for the manufacturer to provide an output
frequency that is proportional to the energy or active power
under steady load conditions. This output frequency can provide a
If 0 were written to any of the frequency division registers, the
divider would use 1 in the frequency division. In addition, the
ratio APCFNUM/APCFDEN should be set not greater than 1 to
ensure proper operation. In other words, the APCF output
frequency cannot be higher than the frequency on the DFC output.
The output frequency has a slight ripple at a frequency equal to
2× the line frequency. This is due to imperfect filtering of the
instantaneous power signal to generate the active power signal
Rev. E | Page 33 of 72
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ADE7761AARSZ-RL IC ENERGY METERING 1PHASE 20SSOP
ADE7761BARSZ-RL IC ENERGY METERING 1PHASE 20SSOP
ADE7768ARZ-RL IC ENERGY METERING 1PHASE 16SOIC
ADE7769ARZ-RL IC ENERGY METERING 1PHASE 16SOIC
ADM8843ACPZ-REEL7 IC LED DRVR WHITE BCKLGT 16LFCSP
ADP1653ACPZ-R7 IC LED DRVR PHOTO FLASH 16-LFCSP
ADP1712-EVALZ BOARD EVALUATION ADP1712
ADP1720-EVALZ BOARD EVAL FOR ADP1720-ADJ
相关代理商/技术参数
ADE7759 制造商:AD 制造商全称:Analog Devices 功能描述:Active Energy Metering IC with di/dt Sensor Interface
ADE7759ARS 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSRL 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSZ 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7759ARSZRL 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7760 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection
ADE7760ARS 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP 制造商:Analog Devices 功能描述:ENERGY METER IC W/ ONCHIP FAULT & OSCIL. - Rail/Tube
ADE7760ARSRL 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP T/R 制造商:Analog Devices 功能描述:ENERGY METER IC W/ONCHIP FAULT & OSCIL. - Tape and Reel